Model — XL

FalsMount XL 551–600 mm

The no-drill standing-seam Starlink mount, XL length. Clamps the seam, carries a 42.4 mm tube and compensates roof pitches of 0–45° so the tube stands vertical.

€249per mount

Final price plus shipping. No VAT added.

A Starlink dish on a galvanised FalsMount mount clamped to the seams of a dark standing-seam metal roof

Starlink pipe adapter: included in the Starlink Mini kit. For Standard and Performance it is not in the box and is sold separately in the Starlink shop. It fits our standing tube.

Built to your seam step.

mm

Measured between two seam folds. The XL is cut to this dimension.

This length is over the standard parcel limit. We'll confirm delivery time and shipping cost before you pay. Shipping & delivery

Cut to your seam step, so it cannot be returned for fit — measure twice. Returns & refunds

Specification

Seam step (cover width)
551–600 mm
Base plate length
600–605 mm
Seam height
23–37 mm
Roof-pitch compensation
0–45°
Tube diameter
42.4 mm
Materials
galvanized steel
The clamp grips the standing-seam fold itself (Orima CHA077, made in Finland). We publish a measured working band for fold height of 23–37 mm with these clamps — our measurement, not yet a figure confirmed by Orima. Near either end of that band, send a photo and a measurement before ordering.Starlink pipe adapter: included in the Starlink Mini kit. For Standard and Performance it is not in the box and is sold separately in the Starlink shop. It fits our standing tube.Only the Orima clamps touch the roof; they are galvanised steel. The base plate sits clear of the roof sheet.Roof clamps: Orima CHA077 (made in Finland).
Wind load: Eurocode design basis, wind zones 1–2

The wind load is calculated per DIN EN 1991-1-4 (German NA) as a design basis. The calculated verification of the mount against this load is not yet complete. There is no structural engineer review and no certificate; we do not state a certified wind speed. Design basis: wind zones 1–2, terrain category II, up to 10 m building height.

Higher wind zones (coast, North Sea islands) and buildings over 10 m are outside our design basis — send your location and a photo.

About German wind zones

Germany has four wind zones (1–4); our design basis covers zones 1–2. To look yours up: the wind-zone map in the National Annex to DIN EN 1991-1-4, or your engineer / installer.

About wind and snow loads

Final price — no VAT added

FalsMount sells from the EU. The seller is not VAT-registered and does not add VAT. The listed product price is final; shipping may still be added at checkout. Details in the legal notice.

Which standing-seam roofs each model fits

The assembly

FIG. 1 — SEAM CLAMP + PIVOT ARM (3D MODEL)DRAG TO ROTATE
CAD assembly — seam clamp, adjustable pivot arm and standing tube. Drag to rotate, scroll to zoom.
FIG. 2 — IN PLACE ON A STANDING-SEAM ROOF (ILLUSTRATION)NOT TO SCALE
Line illustration of the FalsMount seam clamp, pivot arm and tube carrying a Starlink dish on a standing-seam metal roof
The clamps close on two seams, the plate spans the step between them and the tube carries the dish clear of the roof. Illustration — take dimensions from the specification above, not from the drawing.

Installation guide

FAQ

Which clamps are in the box? Orima CHA077 standing-seam clamps, made in Finland. The pivot arm, plate and tube are the FalsMount assembly.

Is VAT added to the listed price? No. The seller is not VAT-registered and does not charge VAT. The listed product price is the final price — nothing is added for VAT. Shipping may still be added at checkout.

What if it doesn't fit? The XL is cut to the seam step you enter, so it cannot be returned for fit — check your measurement before ordering. Defects are covered by the statutory warranty. Details on the returns page.

How do I install it? Step-by-step on the installation guide.